Description

Applicable on Brocade SAN switch. Tested on a Brocade Silkworm series and VDX Series Fibre Channel Switch. Monitors the status values of temperature, fan, power supply monitors and operational status, flash operational status and SFP stats, etc. Use the Fiber Channel templates along with this template.

Prerequisites

SNMP should be enabled in end device and device should support SW-MIB OIDs and SNMP credentials should be attached against the device in portal.

How to Apply: This template is All instance selection based and Automatic select instance based. It will not ask user to select any instance (s) while assigning it to a device.

Metric Parameters

Metric Parameters
ParameterDescription
Frequency
  • Frequency is the interval in which you want to probe and collect metric data from the target device/resource
  • Frequency is defined in minutes (min).
  • Warning ThresholdIf the metric value satisfies the condition defined along with Warning Threshold value, then a notification is sent to the user.
    Critical ThresholdIf the metric value satisfies the condition defined along with Critical Threshold value, then a notification is sent to the user.
    AlertThe alert value can be set to either Yes or No. If it is Yes, then an alert message is sent to the user.

    Metrics

    system.fan.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3
    ExpressionNULL
    DescriptionMonitors the current status of the fan sensor. Possible values are 1- normal,2- faulty, 3- below-min, 4- nominal, 5- above-max, 6- absent. [OIDs: 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.5, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.2]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade SAN Switch Fan
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterswSensorType
    ==
    2
    Warning OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold1,6[{"1":"normal"},{"2":"faulty"},{"3":"below-min"},{"4":"nominal"},{"5":"above-max"},{"6":"absent"}]
    Warning Repeat Count11-12
    Critical OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold2,3,5[{"1":"normal"},{"2":"faulty"},{"3":"below-min"},{"4":"nominal"},{"5":"above-max"},{"6":"absent"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)NoYes/No

    Sample Output

    No graph

    system.fan.speed

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4
    ExpressionNULL
    DescriptionMonitors the current value (reading) of the fan sensor. The value, -2147483648, represents an unknown quantity. It also means that the sensor does not have the capability to measure the actual value. [OID: 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.5, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.2]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade SAN Switch Fan
    Unitrpm

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterswSensorType
    ==
    2
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    brocade.san.switch.operational.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.1.7.0,
    1.3.6.1.4.1.1588.2.1.1.1.1.8.0
    Expressionif((swAdmStatus==1),swOperStatus,0)
    DescriptionMonitors the current operational status of the switch. Possible operational status values are 1- Online : the switch is accessible by an external fibre channel port, 2- Offline : the switch is not accessible, 3- Testing : the switch is in a built-in test mode and is not accessible by an external fibre channel port, 4- Faulty : the switch is not operational. [OIDs: 1.3.6.1.4.1.1588.2.1.1.1.1.7, 1.3.6.1.4.1.1588.2.1.1.1.1.8]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade SAN Switch Operational Status
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold2,3[{"1":"online"},{"2":"offline"},{"3":"testing"},{"4":"faulty"},{"0":"adminDown"}]
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold4[{"1":"online"},{"2":"offline"},{"3":"testing"},{"4":"faulty"},{"0":"adminDown"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Brocade SAN Switch Operational Status

    Brocade SAN Switch Operational Status

    brocade.san.switch.flash.operational.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.1.11.0,
    1.3.6.1.4.1.1588.2.1.1.1.1.12.0
    Expressionif((swFlashDLAdmStatus==1),swFlashDLOperStatus,-1)
    DescriptionMonitors the flash operational status of the switch. Possible flash operational status values are 0- Unknown , 1- SW current : the flash contains the current firmware image or configuration file, 2- SW fw upgraded : the flash contains the image upgraded from the flash DL host, 3- SW Cf Uploaded : the switch configuration file has been uploaded to the host, 4- SW Cf Downloaded : the switch configuration file has been downloaded from the host, 5- SW Fw corrupted : the firmware in the flash of the switch is corrupted. [OIDs: 1.3.6.1.4.1.1588.2.1.1.1.1.11, 1.3.6.1.4.1.1588.2.1.1.1.1.12]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade SAN Switch Operational Status
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold5[{"0":"unknown"},{"1":"swCurrent"},{"2":"swFwUpgraded"},{"3":"swCfUploaded"},{"4":"swCfDownloaded"},{"5":"swFwCorrupted"},{"-1":"adminDown"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Brocade SAN Switch Flash Operational Status

    Brocade SAN Switch Flash Operational Status

    brocade.san.switch.power.supply.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3
    ExpressionNULL
    DescriptionMonitors the current status of the power supply sensor. Possible values are 1- unknown,2- faulty, 3- below-min, 4- nominal, 5- above-max, 6- absent. [OIDs: 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.5, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.2]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade SAN Switch Power Supply
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterswSensorType
    ==
    3
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold1[{"1":"unknown"},{"2":"faulty"},{"3":"below-min"},{"4":"nominal"},{"5":"above-max"},{"6":"absent"}]
    Warning Repeat Count11-12
    Critical OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold2,3,5[{"1":"unknown"},{"2":"faulty"},{"3":"below-min"},{"4":"nominal"},{"5":"above-max"},{"6":"absent"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)NoYes/No

    Sample Output

    No graph

    brocade.san.switch.power.supply.value

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4
    ExpressionNULL
    DescriptionMonitors the current value (reading) of the power supply sensor. The value, -2147483648, represents an unknown quantity. It also means that the sensor does not have the capability to measure the actual value. [OID: 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.5, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.2]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade SAN Switch Power Supply
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterswSensorType
    ==
    3
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Power Supply Sensor Value

    Power Supply Sensor Value

    system.temperature.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3
    ExpressionNULL
    DescriptionMonitors the current status of the temperature sensor. Possible values are 1- unknown,2- faulty, 3- below-min, 4- nominal, 5- above-max, 6- absent. [OIDs: 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.5, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.2]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade SAN Switch Temperature
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterswSensorType
    ==
    1
    Warning OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold1,6[{"1":"unknown"},{"2":"faulty"},{"3":"below-min"},{"4":"nominal"},{"5":"above-max"},{"6":"absent"}]
    Warning Repeat Count11-12
    Critical OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold2,3,5[{"1":"unknown"},{"2":"faulty"},{"3":"below-min"},{"4":"nominal"},{"5":"above-max"},{"6":"absent"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)NoYes/No

    Sample Output

    No graph

    system.temperature.value

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4
    ExpressionNULL
    DescriptionMonitors the current value (reading) of the temperature sensor. The value, -2147483648, represents an unknown quantity. It also means that the sensor does not have the capability to measure the actual value. [OID: 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.5, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.3, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.4, 1.3.6.1.4.1.1588.2.1.1.1.1.22.1.2]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade SAN Switch Temperature
    UnitC

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterswSensorType
    ==
    1
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Temperature Sensor Value

    Temperature Sensor Value

    brocade.switch.fru.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.2.1.5.1.2
    ExpressionNULL
    DescriptionMonitors the current status of the FRU object in the slot. Possible values are 1- other, 2- unknown, 3- on, 4- off, 5- faulty. [OIDs: 1.3.6.1.4.1.1588.2.1.2.1.5.1.2, 1.3.6.1.2.1.47.1.1.1.1.7]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade Switch Additional HA-MIB Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold2,4[{"1":"other"},{"2":"unknown"},{"3":"on"},{"4":"off"},{"5":"faulty"}]
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold5[{"1":"other"},{"2":"unknown"},{"3":"on"},{"4":"off"},{"5":"faulty"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    FRU Status

    FRU Status

    brocade.switch.cp.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.2.1.7.1.1
    ExpressionNULL
    DescriptionMonitors the current status of the Control Processor (CP). Possible values are 1- other, 2- unknown, 3- active, 4- standby, 5- failed. [OIDs: 1.3.6.1.2.1.47.1.1.1.1.7, 1.3.6.1.4.1.1588.2.1.2.1.7.1.1]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade Switch Additional HA-MIB Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold2,4[{"1":"other"},{"2":"unknown"},{"3":"active"},{"4":"standby"},{"5":"failed"}]
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold5[{"1":"other"},{"2":"unknown"},{"3":"active"},{"4":"standby"},{"5":"failed"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    brocade.switch.bp.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.2.1.8.1.1
    ExpressionNULL
    DescriptionMonitors the Blade Processor (BP) status. Possible values are 1- on, 2- off, 3- faulty, 4- unknown, 5- others. [OIDs: 1.3.6.1.2.1.47.1.1.1.1.7, 1.3.6.1.4.1.1588.2.1.2.1.8.1.1]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade Switch Additional HA-MIB Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold4[{"1":"on"},{"2":"off"},{"3":"faulty"},{"4":"unknown"},{"5":"others"}]
    Warning Repeat Count11-12
    Critical OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold2,3[{"1":"on"},{"2":"off"},{"3":"faulty"},{"4":"unknown"},{"5":"others"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    brocade.switch.beacon.operational.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.1.18.0
    ExpressionNULL
    DescriptionMonitors the current operational status of the switch beacon. When the beacon is on (1), the LEDs on the front panel of the switch run alternately from left to right and right to left. The color is yellow. When the beacon is off (2), each LED will be in its regular status indicating color and state. [OID: 1.3.6.1.4.1.1588.2.1.1.1.1.18.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade Switch Additional Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold1[{"1":"on"},{"2":"off"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Switch Beacon Operational Status

    Switch Beacon Operational Status

    brocade.switch.cpu.utilization

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.26.1.0
    ExpressionNULL
    DescriptionMonitors the system's cpu usage. [OID: 1.3.6.1.4.1.1588.2.1.1.1.26.1.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade Switch Additional Monitors
    Unit%

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold800-100
    Warning Repeat Count11-12
    Critical OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold900-100
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Switch CPU Utilization

    Switch CPU Utilization

    brocade.switch.memory.utilization

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.26.6.0
    ExpressionNULL
    DescriptionMonitors the system's memory usage. [OID: 1.3.6.1.4.1.1588.2.1.1.1.26.6.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade Switch Additional Monitors
    Unit%

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold800-100
    Warning Repeat Count11-12
    Critical OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold900-100
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Switch Memory Utilization

    Switch Memory Utilization

    brocade.switch.ha.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.2.1.1.0
    ExpressionNULL
    DescriptionMonitors whether the system is redundant or not. Possible values are 0- redundant, 1- nonredundant. [OID: 1.3.6.1.4.1.1588.2.1.2.1.1.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade Switch Additional Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold1[{"0":"redundant"},{"1":"nonredundant"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    High Availability Status

    High Availability Status

    switch.fiberchannel.port.oper.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.6.2.1.4,
    1.3.6.1.4.1.1588.2.1.1.1.6.2.1.5
    Expressionif((swFCPortAdmStatus==1),swFCPortOpStatus,-1)
    DescriptionMonitors the the operational status of the port. The online(1) state indicates that user frames can be passed. The unknown(0) state indicates that likely the port module is physically absent. Other possible states are 2- Offline, 3- testing, 4- faulty. [OIDs: 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.4, 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.5, 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.36]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade Switch FC Port Operational Status
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold0,3[{"0":"unknown"},{"1":"online"},{"2":"offline"},{"3":"testing"},{"4":"faulty"},{"-1":"AdminstrativelyDown"}]
    Warning Repeat Count11-12
    Critical OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold2,4[{"0":"unknown"},{"1":"online"},{"2":"offline"},{"3":"testing"},{"4":"faulty"},{"-1":"AdminstrativelyDown"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Switch FC Port Operational Status

    Switch FC Port Operational Status

    brocade.switch.fc.port.physical.state

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.6.2.1.3
    ExpressionNULL
    DescriptionThis object identifies the physical state of the port: 1- No Card- no card present in this switch slot, 2- No Transceiver- no transceiver module in this port (noGbic(2) was used previously. Transceiver is the generic name for GBIC, SFP etc.), 3- Laser Fault- the module is signaling a laser fault (defective Transceiver), 4- No Light- the module is not receiving light, 5- No Sync- the module is receiving light but is out of sync, 6- In Sync- the module is receiving light and is in sync, 7- Port Fault- the port is marked faulty (defective Transceiver, cable or device), 8- DiagFault- the port failed diagnostics (defective G_Port or FL_Port card or motherboard), 9- Lock Ref- the port is locking to the reference signal. Alert is generated when the physical state is equal to 4- No Light, 7- Port Fault. [OIDs: 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.1, 1.3.6.1.4.1.1588.2.1.1.1.6.2.1.3]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade FC Port Physical Status
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorNOT_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold6[{"1":"noCard"},{"2":"noTransceiver"},{"3":"laserFault"},{"4":"noLight"},{"5":"noSync"},{"6":"inSync"},{"7":"portFault"},{"8":"diagFault"},{"9":"lockRef"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    FC Port Physical State

    FC Port Physical State

    brocade.san.switch.sfp.current

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.28.1.1.3
    ExpressionswSfpCurrent/1000
    DescriptionMonitors the current of SFP in amps. [OID: 1.3.6.1.4.1.1588.2.1.1.1.28.1.1.3]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade SAN Switch SFP Current
    Unitamps

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterswSfpCurrent
    Not Equals Ignore Case
    NA
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    SFP Current

    SFP Current

    brocade.san.switch.sfp.rxpower

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.28.1.1.4
    ExpressionNULL
    DescriptionMonitors the Rx power consumption of SFP in dBm. [OID: 1.3.6.1.4.1.1588.2.1.1.1.28.1.1.4]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade SAN Switch SFP Rx Power
    UnitdBm

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterswSfpRxPower
    Regex match
    [+-]?d+.?d*
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    SFP Rx Power

    SFP Rx Power

    brocade.san.switch.sfp.temperature

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.28.1.1.1
    ExpressionNULL
    DescriptionMonitors the temperature of SFP in centigrade. [OID: 1.3.6.1.4.1.1588.2.1.1.1.28.1.1.1]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade SAN Switch SFP Temperature
    UnitC

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterswSfpRxPower
    Regex match
    [+-]?d+.?d*
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    SFP Temperature

    SFP Temperature

    brocade.san.switch.sfp.txpower

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.28.1.1.5
    ExpressionNULL
    DescriptionMonitors the Tx power consumption of SFP. [OID: 1.3.6.1.4.1.1588.2.1.1.1.28.1.1.5]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade SAN Switch SFP Tx Power
    UnitdBm

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterswSfpTxPower
    Not Equals Ignore Case
    NA
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    SFP Tx Power

    SFP Tx Power

    brocade.san.switch.sfp.voltage

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.1588.2.1.1.1.28.1.1.2
    ExpressionNULL
    DescriptionMonitors the voltage of SFP in millivolts. [OID: 1.3.6.1.4.1.1588.2.1.1.1.28.1.1.2]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameBrocade SAN Switch SFP Voltage
    UnitmV

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterswSfpVoltage
    Not Equals Ignore Case
    NA
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    SFP Voltage

    SFP Voltage