Description

[CISCO-RTTMON-ICMP-MIB] It monitors the Cisco IP SLA ICMP Jitter operation statistics like packet loss, successful RTT’s, out-of-sequence packets (Source->Destination and Destination->Source), RTT operation status, late packets, one way trip time packets, average jitter(Source->Destination and Destination->Source and sum of both directions), average one-way latency(Source->Destination and Destination->Source) and average RTT. It collects these statistics using SNMP OIDs. Validated this template on SysObjID: 1.3.6.1.4.1.9.1.576 (C2800NM-SPSERVICESK9-M).

Prerequisites

SNMP should be enabled in end device and device should support CISCO-RTTMON-ICMP-MIB, CISCO-RTTMON-MIB OIDs and SNMP credentials should be attached against the device in portal.

How to Apply: This template is All instance selection based. It will not ask user to select any instance (s) while assigning it to a device.

Metric Parameters

Metric Parameters
ParameterDescription
Frequency
  • Frequency is the interval in which you want to probe and collect metric data from the target device/resource
  • Frequency is defined in minutes (min).
  • Warning ThresholdIf the metric value satisfies the condition defined along with Warning Threshold value, then a notification is sent to the user.
    Critical ThresholdIf the metric value satisfies the condition defined along with Critical Threshold value, then a notification is sent to the user.
    AlertThe alert value can be set to either Yes or No. If it is Yes, then an alert message is sent to the user.

    Metrics

    cisco.rttmon.jitter.icmp.numrtt

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.42.1.5.4.1.1, 1.3.6.1.4.1.9.9.42.1.2.1.1.4
    ExpressionrttMonLatestIcmpJitterNumRTT
    DescriptionThe number of RTT's that were successfully measured. [OID: 1.3.6.1.4.1.9.9.42.1.5.4.1.1]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco IP SLA ICMP Jitter Operation Stats - SNMP
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Note: As Alert is not enabled on the above metric, the fields are left blank.

    Sample Output

    No graph

    cisco.rttmon.jitter.icmp.pl

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.42.1.5.4.1.26
    ExpressionNULL
    DescriptionThe number of packets lost. [OID: 1.3.6.1.4.1.9.9.42.1.5.4.1.26]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco IP SLA ICMP Jitter Operation Stats - SNMP
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorGREATER_THANEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold30 - 4294967295
    Warning Repeat Count11-12
    Critical OperatorGREATER_THANEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold60 - 4294967295
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    cisco.rttmon.jitter.icmp.pktoutseq.sd

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.42.1.5.4.1.28
    ExpressionNULL
    DescriptionThe number of packets arrived out of sequence in the direction of source-to-destination.
    [OID: 1.3.6.1.4.1.9.9.42.1.5.4.1.28]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco IP SLA ICMP Jitter Operation Stats - SNMP
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Note: As Alert is not enabled on the above metric, the fields are left blank.

    Sample Output

    No graph

    cisco.rttmon.jitter.icmp.pktoutseq.ds

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.42.1.5.4.1.29
    ExpressionNULL
    DescriptionThe number of packets arrived out of sequence in the direction of destination-to-source.
    [OID: 1.3.6.1.4.1.9.9.42.1.5.4.1.29]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco IP SLA ICMP Jitter Operation Stats - SNMP
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Note: As Alert is not enabled on the above metric, the fields are left blank.

    Sample Output

    No graph

    cisco.rttmon.jitter.icmp.jittersense

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.42.1.5.4.1.31
    ExpressionNULL
    DescriptionAn application specific sense code for the completion status of a RTT operation. These are the defined values: other(0) - the operation is not started or completed or this object is not applicable for the probe type; ok(1) - a valid completion occurred and timed successfully; disconnected(2) - the operation did not occur because the connection to the target was lost; overThreshold(3) - a valid completion was received but the completion time exceeded a threshold value; timeout(4) - an operation timed out; no completion time recorded; busy(5) - the operation did not occur because a previous operation is still outstanding; notConnected(6) - the operation did not occur because no connection (session) exists with the target; dropped(7) - the operation did not occur due to lack of internal resource; sequenceError(8) - a completed operation did not contain the correct sequence id; no completion time recorded; verifyError(9) - a completed operation was received, but the data it contained did not match the expected data; no completion time recorded; applicationSpecific(10) - the application generating the operation had a specific error; dnsServerTimeout(11) - DNS Server Timeout; tcpConnectTimeout(12) - TCP Connect Timeout; httpTransactionTimeout(13) - HTTP Transaction Timeout; dnsQueryError(14) - DNS Query error (because of unknown address etc.,); httpError(15) - HTTP Response StatusCode is not OK (200),or permenent redirect(301), temporary redirect(302) then HTTP error is set; error(16) - if there are socket failures or some other errors not relavant to the actual probe, they are recorded under this error; mplsLspEchoTxError(17) - MPLS echo request transmission failure.; mplsLspUnreachable(18) - MPLS Target FEC not reachable or unsupported mpls echo reply code; mplsLspMalformedReq(19) - MPLS echo request was malformalformed, pointed out by the reply router; mplsLspReachButNotFEC(20) - MPLS echo request processed by the downstream router but not the target; enableOk(21) - Control enable request OK; enableNoConnect(22) - Control enable request fail due to no connection to the target; enableVersionFail(23) - Control enable request version fail; enableInternalError(24) - Control enable request internal error; enableAbort(25) - Control enable request abort; enableFail(26) - Control enable request fail; enableAuthFail(27) - Control enable request fail due to authentication fail; enableFormatError(28) - Control enable request fail due to format error; enablePortInUse(29) - Control enable request fail due to port in use; statsRetrieveOk(30) - Stats retrieve request OK; statsRetrieveNoConnect(31) - Stats retrieve request fail due to no connection to the target; statsRetrieveVersionFail(32) - Stats retrieve request version fail; statsRetrieveInternalError(33) - Stats retrieve request internal error; statsRetrieveAbort(34) - Stats retrieve request abort; statsRetrieveFail(35) - Stats retrieve request fail; statsRetrieveAuthFail(36) - Stats retrieve request fail due to authentication fail; statsRetrieveFormatError(37) - Stats retrieve request fail due to format error; statsRetrievePortInUse(38) - Stats retrieve request fail due to port in use.
    [OID: 1.3.6.1.4.1.9.9.42.1.5.4.1.31]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco IP SLA ICMP Jitter Operation Stats - SNMP
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Note: As Alert is not enabled on the above metric, the fields are left blank.

    Sample Output

    No graph

    cisco.rttmon.jitter.icmp.pkt.late

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.42.1.5.4.1.32
    ExpressionNULL
    DescriptionThe number of packets that arrived after the timeout. [OID: 1.3.6.1.4.1.9.9.42.1.5.4.1.32]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco IP SLA ICMP Jitter Operation Stats - SNMP
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Note: As Alert is not enabled on the above metric, the fields are left blank.

    Sample Output

    No graph

    cisco.rttmon.jitter.icmp.numow

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.42.1.5.4.1.43
    ExpressionNULL
    DescriptionThe number of successful one way trip time measurements. [OID: 1.3.6.1.4.1.9.9.42.1.5.4.1.43]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco IP SLA ICMP Jitter Operation Stats - SNMP
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Note: As Alert is not enabled on the above metric, the fields are left blank.

    Sample Output

    No graph

    cisco.rttmon.jitter.icmp.avgjitter

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.42.1.5.4.1.44
    ExpressionNULL
    DescriptionThe average of positive and negative jitter values in Source-to-Destionation and Destination-to-Source direction. [OID: 1.3.6.1.4.1.9.9.42.1.5.4.1.44]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco IP SLA ICMP Jitter Operation Stats - SNMP
    Unitms

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Note: As Alert is not enabled on the above metric, the fields are left blank.

    Sample Output

    No graph

    cisco.rttmon.jitter.icmp.avgjitter.sd

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.42.1.5.4.1.45
    ExpressionNULL
    DescriptionThe average of positive and negative jitter values from source to destination.
    [OID: 1.3.6.1.4.1.9.9.42.1.5.4.1.45]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco IP SLA ICMP Jitter Operation Stats - SNMP
    Unitms

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Note: As Alert is not enabled on the above metric, the fields are left blank.

    Sample Output

    No graph

    cisco.rttmon.jitter.icmp.avgjitter.ds

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.42.1.5.4.1.46
    ExpressionNULL
    DescriptionThe average of positive and negative jitter values from destination to source.
    [OID: 1.3.6.1.4.1.9.9.42.1.5.4.1.46]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco IP SLA ICMP Jitter Operation Stats - SNMP
    Unitms

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Note: As Alert is not enabled on the above metric, the fields are left blank.

    Sample Output

    No graph

    cisco.rttmon.jitter.icmp.owavgsd

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.42.1.5.4.1.47
    ExpressionNULL
    DescriptionThe average one way trip time from source to destination. [OID: 1.3.6.1.4.1.9.9.42.1.5.4.1.47]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco IP SLA ICMP Jitter Operation Stats - SNMP
    Unitms

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorGREATER_THANEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold30 - 4294967295
    Warning Repeat Count11-12
    Critical OperatorGREATER_THANEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold50 - 4294967295
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    cisco.rttmon.jitter.icmp.owavgds

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.42.1.5.4.1.48
    ExpressionNULL
    DescriptionThe average one way trip time from destination to source. [OID: 1.3.6.1.4.1.9.9.42.1.5.4.1.48]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco IP SLA ICMP Jitter Operation Stats - SNMP
    Unitms

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorGREATER_THANEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold30 - 4294967295
    Warning Repeat Count11-12
    Critical OperatorGREATER_THANEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold50 - 4294967295
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    cisco.rttmon.jitter.icmp.avgrtt

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.42.1.5.4.1.2
    Expression(rttMonLatestIcmpJitterRTTSum / rttMonLatestIcmpJitterNumRTT)
    DescriptionAverage Round-Trip Time in milliseconds. Expression: (rttMonLatestIcmpJitterRTTSum / rttMonLatestIcmpJitterNumRTT) [OIDs: 1.3.6.1.4.1.9.9.42.1.5.4.1.1, 1.3.6.1.4.1.9.9.42.1.5.4.1.2]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco IP SLA ICMP Jitter Operation Stats - SNMP
    Unitms

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Note: As Alert is not enabled on the above metric, the fields are left blank.

    Sample Output

    No graph