Description

It monitors the Cisco L4-L7 module’s resource utilization. The resources configured are of following categories: 1) TCP/IP Connections, 2) MAC Addresses, 3)syslog buffer, ACL Memmory, 4) NAT Translations etc. This template is validated on Cisco ASA Version 9.1(7)7, SysObjID: 1.3.6.1.4.1.9.1.915.

Prerequisites

SNMP should be enabled in end device and device should support CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB OIDs and SNMP credentials should be attached against the device in portal.

How to Apply: This template is All instance selection based. It will not ask user to select any instance (s) while assigning it to a device.

Metric Parameters

Metric Parameters
ParameterDescription
Frequency
  • Frequency is the interval in which you want to probe and collect metric data from the target device/resource
  • Frequency is defined in minutes (min).
  • Warning ThresholdIf the metric value satisfies the condition defined along with Warning Threshold value, then a notification is sent to the user.
    Critical ThresholdIf the metric value satisfies the condition defined along with Critical Threshold value, then a notification is sent to the user.
    AlertThe alert value can be set to either Yes or No. If it is Yes, then an alert message is sent to the user.

    Metrics

    cisco.l4l7.module.resource.usage

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.480.1.1.2.1.8
    ExpressionNULL
    DescriptionMonitors the number of resources identified by 'ciscoResourceLimitType', that are currently being used in the system. It will alert if crlResourceLimitCurrentUsage > crlResourceLimitMax. [CISCO-L4L7MODULE-RESOURCE-LIMIT-MIB::crlResourceLimitCurrentUsage::1.3.6.1.4.1.9.9.480.1.1.2.1.8, crlResourceLimitMax::1.3.6.1.4.1.9.9.480.1.1.2.1.5]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco L4-L7 Module's Resource Usage
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Note: As Alert is not enabled on the above metric, the fields are left blank.

    Sample Output

    No graph

    cisco.l4l7.module.resource.usage.notify

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.9.9.480.1.1.2.1.5
    Expressionif(cisco.l4l7.module.resource.usage > crlResourceLimitMax,1,0)
    DescriptionIt monitors the number of resources identified by 'crlRateLimitResourceType' object, that are currently being used in the system. This metric is applicable on L4-L7 Modules. It alerts when the module's resource utilization exceeds the max resource limit configured in the system (crlResourceLimitCurrentUsage > crlResourceLimitMax). [OIDs: crlResourceLimitCurrentUsage - 1.3.6.1.4.1.9.9.480.1.1.2.1.8, crlResourceLimitMax - 1.3.6.1.4.1.9.9.480.1.1.2.1.5]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCisco L4-L7 Module's Resource Usage
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold10 - 4294967295
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)NoYes/No

    Sample Output

    No graph