Description

Applicable on EqualLogic SAN devices. Monitors the disk Status, disk performance, Controller Battery Status, Volume status, Group and Member performance and storage, etc.

Prerequisites

SNMP should be enabled in end device and device should support EQLCONTROLLER-MIB, EQLSTORAGE-MIB, EQLVOLUME-MIB, EQLDISK-MIB, EQLGROUP-MIB, EQLMEMBER-MIB OIDs and SNMP credentials should be attached against the device in portal.

How to Apply: This template is All instance selection based. It will not ask user to select any instance(s) while assigning it to a device.

Metric Parameters

Metric Parameters
ParameterDescription
Frequency
  • Frequency is the interval in which you want to probe and collect metric data from the target device/resource
  • Frequency is defined in minutes (min).
  • Warning ThresholdIf the metric value satisfies the condition defined along with Warning Threshold value, then a notification is sent to the user.
    Critical ThresholdIf the metric value satisfies the condition defined along with Critical Threshold value, then a notification is sent to the user.
    AlertThe alert value can be set to either Yes or No. If it is Yes, then an alert message is sent to the user.

    Metrics

    controller.battery.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.4.1.1.1.5
    ExpressionNULL
    DescriptionMonitors the controller battery status. Possible values are 1- ok , 2- failed , 3- good-battery-is-charging , 4- low-voltage-status, 5- low-voltage-is-charging , 6- missing-battery. [OID: 1.3.6.1.4.1.12740.4.1.1.1.5]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell EqualLogic Controller Battery
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold4[{"1":"ok"},{"2":"failed"},{"3":"good-battery-is-charging"},{"4":"low-voltage-status"},{"5":"low-voltage-is-charging"},{"6":"missing-battery"}]
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold2[{"1":"ok"},{"2":"failed"},{"3":"good-battery-is-charging"},{"4":"low-voltage-status"},{"5":"low-voltage-is-charging"},{"6":"missing-battery"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Controller Battery Status

    Controller Battery Status

    controller.nvrambattery.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.4.1.1.1.32
    ExpressionNULL
    DescriptionMonitors the status of NVRAM Battery on CM. Possible values are 0- not-present, 1- good, 2- bad, 3- unknown. [OID: 1.3.6.1.4.1.12740.4.1.1.1.32]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell EqualLogic Controller Battery
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold3[{"0":"not-present"},{"1":"good"},{"2":"bad"},{"3":"unknown"}]
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold2[{"0":"not-present"},{"1":"good"},{"2":"bad"},{"3":"unknown"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Controller NVRAM Battery Status

    Controller NVRAM Battery Status

    system.disk.busy.time

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.3.1.2.1.4,
    1.3.6.1.4.1.12740.3.1.1.1.10, 1.3.6.1.4.1.12740.3.1.1.1.11
    ExpressioneqlDiskStatusBusyTime
    DescriptionMonitors the disk time in seconds spent busy. [OIDs: 1.3.6.1.4.1.12740.3.1.2.1.4, 1.3.6.1.4.1.12740.3.1.1.1.10, 1.3.6.1.4.1.12740.3.1.1.1.11]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell EqualLogic Disk Monitors
    Units

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold600 - 4294967295
    Warning Repeat Count11-12
    Critical OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold1200 - 4294967295
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Disk Busy Time

    Disk Busy Time

    system.disk.io.operations.current

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.3.1.2.1.5
    ExpressionNULL
    DescriptionMonitors the number of IO operations currently outstanding. [OID: 1.3.6.1.4.1.12740.3.1.2.1.5]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell EqualLogic Disk Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Disk IO Operations Current

    Disk IO Operations Current

    system.disk.transfers.failed

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.3.1.2.1.6
    ExpressionNULL
    DescriptionMonitors the number of failed transfers. [OID: 1.3.6.1.4.1.12740.3.1.2.1.6]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell EqualLogic Disk Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Disk Transfer Failed

    Disk Transfer Failed

    system.disk.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.3.1.1.1.8,
    1.3.6.1.4.1.12740.3.1.1.1.6
    ExpressioneqlDiskStatus
    DescriptionMonitors the equallogic disk status. Possible status values are 1- on-line: the disk is being used in the raid set, 2- spare: disk is not currently being used by raid configuration but may be used when status of a currently on-line disk changes, 3- failed: either disk is faulted or when there is no power, 4- off-line: disk doesn't fall into any of these other categories, 5- alt-sig: disk belongs to a RAIDset from another EqualLogic system. The disk can be converted to a spare, 6- too-small: drive is too small to be used. The drive cannot be converted to spare, 7- history-of-failures: drive has a history of failures. The drive can be converted to spare, 8- unsupported-version: drive label is from a later release. The drive can be converted to spare, 9- unhealthy: drive is unhealthy, 10- replacement: drive is a replacement drive, 11- encrypted: drive is encrypted and cannot be decrypted, 12- notApproved: drive is not DELL approved, 13- preempt-failed: drive is off-line due to excessive errors. [OID: 1.3.6.1.4.1.12740.3.1.1.1.8]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell EqualLogic Disk Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold4,9,13[{"1":"on-line"},{"2":"spare"},{"3":"failed"},{"4":"off-line"},{"5":"alt-sig"},{"6":"too-small"},{"7":"history-of-failures"},{"8":"unsupported-version"},{"9":"unhealthy"},{"10":"replacement"},{"11":"encrypted"},{"12":"notApproved"},{"13":"preempt-failed"}]
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold3[{"1":"on-line"},{"2":"spare"},{"3":"failed"},{"4":"off-line"},{"5":"alt-sig"},{"6":"too-small"},{"7":"history-of-failures"},{"8":"unsupported-version"},{"9":"unhealthy"},{"10":"replacement"},{"11":"encrypted"},{"12":"notApproved"},{"13":"preempt-failed"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Disk Status

    Disk Status

    equallogic.group.storagepool.free.percent

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.1.1.1.1.20,
    1.3.6.1.4.1.12740.1.1.2.1.1, 1.3.6.1.4.1.12740.1.1.2.1.2, 1.3.6.1.4.1.12740.1.1.2.1.4, 1.3.6.1.4.1.12740.1.1.2.1.15
    Expression(eqlStorageGroupStatusFreeSpace/eqlStorageGroupStatusPoolSpace)*100
    DescriptionMonitors the free space percent of the Storage Pool. [OIDs: 1.3.6.1.4.1.12740.1.1.1.1.19, 1.3.6.1.4.1.12740.1.1.1.1.20, 1.3.6.1.4.1.12740.1.1.2.1.1, 1.3.6.1.4.1.12740.1.1.2.1.2, 1.3.6.1.4.1.12740.1.1.2.1.4, 1.3.6.1.4.1.12740.1.1.2.1.15]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell Equallogic Group Monitors
    Unit%

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorLESS_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold100-100
    Warning Repeat Count11-12
    Critical OperatorLESS_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold50-100
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Storage Pool Free Space Percent

    Storage Pool Free Space Percent

    equallogic.group.members.online

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.1.1.2.1.3
    ExpressionNULL
    DescriptionMonitors the number of group members which are online. [OID: 1.3.6.1.4.1.12740.1.1.2.1.3]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell Equallogic Group Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Online Members

    Online Members

    equallogic.group.members.total

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.1.1.2.1.13
    ExpressionNULL
    DescriptionMonitors the total number of members in this group irrelevant of current member state.
    [OID: 1.3.6.1.4.1.12740.1.1.2.1.13]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell Equallogic Group Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Total Members

    Total Members

    equallogic.group.members.inuse

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.1.1.2.1.14
    ExpressionNULL
    DescriptionMonitors the total number of online+offline members in this group. [OID: 1.3.6.1.4.1.12740.1.1.2.1.14]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell Equallogic Group Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Members in Use

    Members in Use

    equallogic.member.fan

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.2.1.7.1.2,
    1.3.6.1.4.1.12740.2.1.7.1.3, 1.3.6.1.4.1.12740.2.1.7.1.4
    ExpressioneqlMemberHealthDetailsFanCurrentState
    DescriptionMonitors the state of the fan. Possible values are 0- unknown, 1- normal, 2- warning, 3- critical.
    [OIDs: 1.3.6.1.4.1.12740.2.1.7.1.2, 1.3.6.1.4.1.12740.2.1.7.1.3, 1.3.6.1.4.1.12740.2.1.7.1.4]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Member Fan
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold2[{"0":"unknown"},{"1":"normal"},{"2":"warning"},{"3":"critical"}]
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold3[{"0":"unknown"},{"1":"normal"},{"2":"warning"},{"3":"critical"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Members Fan

    Members Fan

    equallogic.member.storage.utilization

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.2.1.1.1.9,
    1.3.6.1.4.1.12740.2.1.10.1.1, 1.3.6.1.4.1.12740.2.1.10.1.2, 1.3.6.1.4.1.12740.2.1.10.1.3, 1.3.6.1.4.1.12740.2.1.10.1.4
    Expression(eqlMemberUsedStorage/eqlMemberTotalStorage)*100
    DescriptionMonitors the equallogic member storage utilization. [OIDs: 1.3.6.1.4.1.12740.2.1.1.1.9, 1.3.6.1.4.1.12740.2.1.10.1.1, 1.3.6.1.4.1.12740.2.1.10.1.2, 1.3.6.1.4.1.12740.2.1.10.1.3, 1.3.6.1.4.1.12740.2.1.10.1.4]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Member Monitors
    Unit%

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold800-100
    Warning Repeat Count11-12
    Critical OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold900-100
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Member Storage Utilization

    Member Storage Utilization

    equallogic.member.storage.total

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OIDNULL
    ExpressioneqlMemberTotalStorage
    DescriptionMonitors the total disk storage in MBs on the array. [OID: 1.3.6.1.4.1.12740.2.1.10.1.1]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Member Monitors
    UnitMB

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Member Storage Total

    Member Storage Total

    equallogic.member.storage.used

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OIDNULL
    ExpressioneqlMemberUsedStorage
    DescriptionMonitors the storage used i.e., sum of reserved delegated space, reserved volume space, used snapshot space, used replication space. [OID: 1.3.6.1.4.1.12740.2.1.10.1.2]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Member Monitors
    UnitMB

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Member Storage Used

    Member Storage Used

    equallogic.member.raid.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.2.1.13.1.1
    ExpressionNULL
    DescriptionMonitors the status of the raid subsystem. This is a composite of the view of the underlying subsystems. Possible values are 1- ok, 2- degraded: in a degraded state, possible because no spare is available, 3- verifying: a verify pass is run, and a percent complete is available, 4- reconstructing: reconstructing a drive and a percent complete is available, 5- a failure while we were up, possibly a drive failed and we have no spare, 6- catastrophicLoss: may not be visible to the user since the member may not be able to bootup. It means we need administrator intervention to correct the problem, 7- expanding, 8- mirroring: mirroring a bad drive onto a spare drive.
    [OID: 1.3.6.1.4.1.12740.2.1.13.1.1]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Member Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold2[{"1":"ok"},{"2":"degraded"},{"3":"verifying"},{"4":"reconstructing"},{"5":"failed"},{"6":"catastrophicLoss"},{"7":"expanding"},{"8":"mirroring"}]
    Warning Repeat Count11-12
    Critical OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold5,6[{"1":"ok"},{"2":"degraded"},{"3":"verifying"},{"4":"reconstructing"},{"5":"failed"},{"6":"catastrophicLoss"},{"7":"expanding"},{"8":"mirroring"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Member Raid Status

    Member Raid Status

    equallogic.member.read.latency

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.2.1.12.1.4
    ExpressionNULL
    DescriptionMonitors the average latency for read operations on this member in milli seconds. The value is reset to zero upon reboot. [OID: 1.3.6.1.4.1.12740.2.1.12.1.4]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Member Monitors
    Unitms

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold10000 - 4294967295
    Warning Repeat Count11-12
    Critical OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold20000 - 4294967295
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Member Read Latency

    Member Read Latency

    equallogic.member.write.latency

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.2.1.12.1.5
    ExpressionNULL
    DescriptionMonitors the average latency for write operations on this member in milli seconds. The value is reset to zero upon reboot. [OID: 1.3.6.1.4.1.12740.2.1.12.1.5]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Member Monitors
    Unitms

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold10000 - 4294967295
    Warning Repeat Count11-12
    Critical OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold20000 - 4294967295
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Member Write Latency

    Member Write Latency

    equallogic.member.iscsi.connections

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.2.1.12.1.1
    ExpressionNULL
    DescriptionMonitors the number of iSCSI connections made from initiators to this array. [OID: 1.3.6.1.4.1.12740.2.1.12.1.1]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Member Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold800-2147483648 and 2147483647
    Warning Repeat Count11-12
    Critical OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold900-2147483648 and 2147483647
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Member iSCSI Connections

    Member iSCSI Connections

    equallogic.member.health

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.2.1.5.1.1
    ExpressionNULL
    DescriptionMonitors the equallogic member health. Possible values are 0 - Unknown, 1 - Normal, 2 - Warning, 3 - Critical. [OID: 1.3.6.1.4.1.12740.2.1.5.1.1]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Member Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold2[{"0":"unknown"},{"1":"normal"},{"2":"warning"},{"3":"critical"}]
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold3[{"0":"unknown"},{"1":"normal"},{"2":"warning"},{"3":"critical"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Member Health

    Member Health

    equallogic.member.power

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.2.1.8.1.2,
    1.3.6.1.4.1.12740.2.1.8.1.3, 1.3.6.1.4.1.12740.2.1.8.1.4
    ExpressioneqlMemberHealthDetailsPowerSupplyCurrentState
    DescriptionMonitors the state of the power supply. Possible values are 1- on-and-operating, 2- no-ac-power, 3- failed-or-no-data. [OIDs: 1.3.6.1.4.1.12740.2.1.8.1.2, 1.3.6.1.4.1.12740.2.1.8.1.3, 1.3.6.1.4.1.12740.2.1.8.1.4]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Member Power Supply
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold2[{"1":"on-and-operating"},{"2":"no-ac-power"},{"3":"failed-or-no-data"}]
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold3[{"1":"on-and-operating"},{"2":"no-ac-power"},{"3":"failed-or-no-data"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Member Power

    Member power

    equallogic.member.temperature

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.2.1.6.1.2,
    1.3.6.1.4.1.12740.2.1.6.1.3
    ExpressioneqlMemberHealthDetailsTemperatureValue
    DescriptionMonitors the temperature in degrees C. [OID: 1.3.6.1.4.1.12740.2.1.6.1.3, 1.3.6.1.4.1.12740.2.1.6.1.2]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Member Temperature
    UnitC

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Member Temperature

    Member Temperature

    equallogic.member.temperature.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.2.1.6.1.4
    ExpressionNULL
    DescriptionMonitors the state of the temperature sensor. Possible values are 0- unknown, 1- normal, 2- warning, 3- critical. [OID: 1.3.6.1.4.1.12740.2.1.6.1.4]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Member Temperature
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold2[{"0":"unknown"},{"1":"normal"},{"2":"warning"},{"3":"critical"}]
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold3[{"0":"unknown"},{"1":"normal"},{"2":"warning"},{"3":"critical"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Member Temperature Status

    Member Temperature Status

    equallogic.replication.storagespace.used

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.16.1.1.1.3,
    1.3.6.1.4.1.12740.16.1.2.1.4, 1.3.6.1.4.1.12740.16.1.2.1.5, 1.3.6.1.4.1.12740.16.1.2.1.6
    Expression(eqlStoragePoolStatsReplicationSpaceUsed/eqlStoragePoolStatsReplicationSpace)*100
    DescriptionMonitors the percentage of space that is currently utilized by replication in this storage pool.
    [OIDs: 1.3.6.1.4.1.12740.16.1.1.1.3, 1.3.6.1.4.1.12740.16.1.2.1.4, 1.3.6.1.4.1.12740.16.1.2.1.5, 1.3.6.1.4.1.12740.16.1.2.1.6]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Storage Pool
    Unit%

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold850-100
    Warning Repeat Count11-12
    Critical OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold900-100
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    equallogic.storagespace.used

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.16.1.1.1.3,
    1.3.6.1.4.1.12740.16.1.2.1.1, 1.3.6.1.4.1.12740.16.1.2.1.2, 1.3.6.1.4.1.12740.16.1.2.1.3
    Expression(eqlStoragePoolStatsSpaceUsed/eqlStoragePoolStatsSpace)*100
    DescriptionMonitors the percentage of the space used by volumes in this pool. [OIDs: 1.3.6.1.4.1.12740.16.1.1.1.3, 1.3.6.1.4.1.12740.16.1.2.1.1, 1.3.6.1.4.1.12740.16.1.2.1.2, 1.3.6.1.4.1.12740.16.1.2.1.3]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Storage Pool
    Unit%

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    equallogic.storagespace.free

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OIDNULL
    Expression(eqlStoragePoolStatsFreeSpace/eqlStoragePoolStatsSpace)*100
    DescriptionMonitors the percentage of space that is available in this storage pool. [OIDs: 1.3.6.1.4.1.12740.16.1.1.1.3, 1.3.6.1.4.1.12740.16.1.2.1.1, 1.3.6.1.4.1.12740.16.1.2.1.2, 1.3.6.1.4.1.12740.16.1.2.1.3]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Storage Pool
    Unit%

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorLESS_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold200-100
    Warning Repeat Count11-12
    Critical OperatorLESS_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold100-100
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Storage Pool Space Free Percent

    Storage Pool Space Free Percent

    volume.replication.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.5.1.7.15.1.2,
    1.3.6.1.4.1.12740.5.1.7.16.1.1
    Expressionif((eqliscsiVolumeReplAdminStatus==1),eqliscsiVolumeReplOperStatus,0)
    DescriptionMonitors the the current operational status of the replication process. Possible status values are 1- Disabled, 2- In Progress, 3- Waiting, 4- Far End Down, 5- Auth Failure, 6- Completed, 7- Paused, 8- Remote Resize Failed, 9- Remote Paused, 10- Partner Paused Local, 11- Failed, 12- Remote ReplReserveLow, 13- Nomoresnapallowed,14- Remote Repl Reserve Invalid, 15- Cancelling, 16- Pending Data Transfer, 17- Manual Data Transfer InProgress, 18- Remote Disallow DowngradesNotSet, 19- Remote Partner Needs Upgrade. [OIDs: 1.3.6.1.4.1.12740.5.1.7.15.1.3, 1.3.6.1.4.1.12740.5.1.7.15.1.2, 1.3.6.1.4.1.12740.5.1.7.16.1.1]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell EqualLogic Volume Replication Status
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold4,5,8,11,15[{"1":"disabled"},{"2":"inProgress"},{"3":"waiting"},{"4":"farEndDown"},{"5":"authFailure"},{"6":"completed"},{"7":"paused"},{"8":"remoteResizeFailed"},{"9":"remotePaused"},{"10":"partnerPausedLocal"},{"11":"failed"},{"12":"remoteReplReserveLow"},{"13":"nomoresnapallowed"},{"14":"remoteReplReserveInvalid"},{"15":"cancelling"},{"16":"pendingDataTransfer"},{"17":"manualDataTransferInProgress"},{"18":"remoteDisallowDowngradesNotSet"},{"19":"remotePartnerNeedsUpgrade"},{"0":"adminDown"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    system.volume.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.12740.5.1.7.7.1.8
    Expression
    DescriptionMonitors the current operational status of the volume. [OIDs: 1.3.6.1.4.1.12740.5.1.7.7.1.8, 1.3.6.1.4.1.12740.5.1.7.1.1.8, 1.3.6.1.4.1.12740.5.1.7.1.1.4]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDELL EqualLogic Volume Status
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold2[{"1":"available"},{"2":"not-available"},{"3":"not-available-due-to-snap-reserve-met"},{"4":"not-available-due-to-members-offline"},{"5":"not-available-due-to-lost-cached-blocks"},{"6":"not-available-due-to-thin-max-growth-met"},{"7":"not-available-due-to-nospace-for-auto-grow"},{"8":"not-available-due-to-missing-pages"},{"9":"not-available-due-to-syncrep"},{"10":"available-no-new-connections"},{"11":"not-available-due-to-internal-error"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Volume Status

    Volume Status