Description

Applicable on Dell Force 10 M series devices. Monitors CPU and memory utilization on the stack units and also it monitors environmental parameters such as power, temperature and fan. Tested on m-MXL (SysObjID: 1.3.6.1.4.1.6027.1.4.1)

Prerequisites

SNMP should be enabled in end device and device should support F10-M-SERIES-CHASSIS-MIB OIDs and SNMP credentials should be attached against the device in portal.

How to Apply: This template is All instance selection based. It will not ask user to select any instance(s) while assigning it to a device.

Metric Parameters

Metric Parameters
ParameterDescription
Frequency
  • Frequency is the interval in which you want to probe and collect metric data from the target device/resource
  • Frequency is defined in minutes (min).
  • Warning ThresholdIf the metric value satisfies the condition defined along with Warning Threshold value, then a notification is sent to the user.
    Critical ThresholdIf the metric value satisfies the condition defined along with Critical Threshold value, then a notification is sent to the user.
    AlertThe alert value can be set to either Yes or No. If it is Yes, then an alert message is sent to the user.

    Metrics

    system.uptime

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.2.1.1.3.0
    ExpressionsysUpTime/100
    DescriptionThe time since the SNMP agent in the system was last re-initialized.[OID : 1.3.6.1.2.1.1.3.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameSystem Uptime
    Units

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    Filter
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorLESS_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold1800
    0 - 4294967295
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Uptime

    Uptime

    dell.force10.stack.unit.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.6027.3.19.1.2.1.1.8
    ExpressionNULL
    DescriptionThe current status of the unit. Possible values are 1 - OK, 2 - Unsupported, 3 - Code mistmatch, 4 - Config mismatch, 5 - Unit down, 6 - Not present.
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell Force10 Stack Unit Monitors - M Series
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorNOT_IN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold1,6[{"1":"ok"},{"2":"unsupported"},{"3":"codeMismatch"},{"4":"configMismatch"},{"5":"unitDown"},{"6":"notPresent"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Stack unit status

    Stack unit status

    dell.force10.unit.temperature

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.6027.3.19.1.2.1.1.14
    ExpressionNULL
    DescriptionThe temperature of the stack unit.
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell Force10 Stack Unit Monitors - M Series
    UnitC

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold65
    0 - 2147483647
    Warning Repeat Count11-12
    Critical OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold70
    0 - 2147483647
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Unit temperature

    Unit temperature

    system.cpu.utilization

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID
    1.3.6.1.4.1.6027.3.19.1.2.8.1.4, 1.3.6.1.4.1.6027.3.19.1.2.8.1.1
    ExpressionchStackUnitCpuUtil5Min
    DescriptionCPU utilization in percentage for last 5 minutes.
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell Force10 Stack Unit Performance Monitor - M Series
    Unit%

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold800-100
    Warning Repeat Count21-12
    Critical OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold900-100
    Critical Repeat Count21-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPU Utilization

    CPU Utilization

    system.memory.util.percent

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID
    1.3.6.1.4.1.6027.3.19.1.2.8.1.5, 1.3.6.1.4.1.6027.3.19.1.2.6.1.4, 1.3.6.1.4.1.6027.3.19.1.2.6.1.3
    ExpressionchStackUnitMemUsageUtil
    DescriptionTotal memory usage in percentage. [OID: 1.3.6.1.4.1.6027.3.19.1.2.8.1.5]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell Force10 Stack Unit Performance Monitor - M Series
    Unit%

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold800-100
    Warning Repeat Count21-12
    Critical OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold900-100
    Critical Repeat Count21-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Memory Utilization

    Memory Utilization

    dell.force10.unit.fan.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.6027.3.19.1.2.3.1.2
    ExpressionNULL
    DescriptionStatus of the Fan tray units. Possible values are 1 - Up, 2 - Down
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell Force10 Stack Unit Fan Status - M Series
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold2[{"1":"up"},{"2":"down"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Unit fan status

    Unit fan status

    dell.force10.unit.power.supply

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID
    1.3.6.1.4.1.6027.3.19.1.2.2.1.2, 1.3.6.1.4.1.6027.3.19.1.2.2.1.3
    ExpressionchSysPowerSupplyOperStatus
    DescriptionPower supply status of the unit. Possible values are 1 - normal, 2 - warning, 3 - critical, 4 - shutdown, 5 - notPresent, 6 - notFunctioning.
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameDell Force10 Stack Unit Power Supply - M Series
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold2[{"1":"normal"},{"2":"warning"},{"3":"critical"},{"4":"shutdown"},{"5":"notPresent"},{"6":"notFunctioning"}]
    Warning Repeat Count11-12
    Critical OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold3,4,6[{"1":"normal"},{"2":"warning"},{"3":"critical"},{"4":"shutdown"},{"5":"notPresent"},{"6":"notFunctioning"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Unit power supply

    Unit power supply