Description

Template for HP ILO (Integrated Lights - Out). Monitors the battery, fan, temperature, fault tolerance power supply status. Also monitors controller battery status, controller interface status, etc. Tested on HP ILO 4 AOS server.

Prerequisites

SNMP should be enabled in end device and device should support CPQSTSYS-MIB, CPQSM2-MIB, CPQSINFO-MIB, CPQSTDEQ-MIB, CPQHLTH-MIB, CPQHLTH-MIBCPQIDA-MIB OIDs and SNMP credentials should be attached against the device in portal.

How to Apply: This template is All instance selection based. It will not ask user to select any instance (s) while assigning it to a device.

Metric Parameters

Metric Parameters
ParameterDescription
Frequency
  • Frequency is the interval in which you want to probe and collect metric data from the target device/resource
  • Frequency is defined in minutes (min).
  • Warning ThresholdIf the metric value satisfies the condition defined along with Warning Threshold value, then a notification is sent to the user.
    Critical ThresholdIf the metric value satisfies the condition defined along with Critical Threshold value, then a notification is sent to the user.
    AlertThe alert value can be set to either Yes or No. If it is Yes, then an alert message is sent to the user.

    Metrics

    hp.ilo.cpq.da.accelerator.error.code

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.3.2.2.2.1.5
    ExpressionNULL
    DescriptionMonitors the drive array accelerator board error code. Used to determine the status of the write cache operations. The status can be: 1- Other: Indicates that the instrument agent does not recognize the error code. You may need to update your software, 2-Invalid: Indicates that write cache operations are currently configured and enabled for at least one logical drive. No write cache errors have occurred, 3- Bad Configuration: Indicates that write cache operations are temporarily disabled. The Array Accelerator board was configured for a different controller. This error could be caused if boards were switched from one system to another. Rerun the configuration utility and ensure that the board has been properly configured for this system. Note: If data from another system was stored on the board,running configuration utility will cause the data to be lost, 4- Low Battery Power: Indicates that write cache operations are temporarily disabled due to insufficient battery power. Please view the Battery Status object instance for more information, 5- Disable Command Issued: Indicates that write cache operations are temporarily disabled. The device driver issues this command when the server is taken down. This condition should not exist when the system regains power, 6- No Resources Available: Indicates that write cache operations are temporarily disabled. The controller does not have sufficient resources to perform write cache operations. For example, when a replaced drive is being rebuilt, there will not be sufficient resources. Once the operation that requires the resources has completed, this condition will clear and write cache operations will resume, 7- Board Not Connected: Indicates that write cache operations are temporarily disabled. The Array Accelerator board has been configured but is not currently attached to the controller. Check the alignment of the board and connections, 8- Bad Mirror Data: Indicates that write cache operations have been permanently disabled. The Array Accelerator board stores mirrored copies of all data. If data exists on the board when the system is first powered up, the board performs a data compare test between the mirrored copies. If the data does not match, an error has occurred. Data may have been lost. Your board may need servicing, 9- Read Failure: Indicates that write cache operations have been permanently disabled. The Array Accelerator board stores mirror copies of all data. While reading the data from the board, memory parity errors have occurred. Both copies were corrupted and cannot be retrieved. Data has been lost, and you should service the board, 10- Write Failure: Indicates that write cache operations have been permanently disabled. This error occurs when an unsuccessful attempt was made to write data to the Array Accelerator board. Data could not be written to write cache memory in duplicate due to the detection of parity errors. This error does not indicate data loss. You should service the Array Accelerator board, 11- Config Command: Indicates that write cache operations have been permanently disabled. The configuration of the logical drives has changed. You need to reconfigure the Array Accelerator board, 12- Expand in Progress: Indicates that cache operations are temporarily disabled due to an expand of a logical drive. When the expand operation completes, the accelerator will be enabled, 13- Snapshot In Progress: Indicates that cache operations are temporarily disabled due to a snapshot operation that is queued up or in progress. When the snapshot operation completes, the accelerator will be enabled, 14- Redundant Low Battery: Indicates that cache operations are temporarily disabled. The redundant controller has insufficient cache battery power, 15- Redundant Size Mismatch: Indicates that cache operations are temporarily disabled. The cache sizes on the redundant controllers do not match, 16- Redundant Cache Failure: Indicates that cache operations are temporarily disabled. The cache on the redundant controller has failed, 17- Excessive ECC Errors: Indicates that write cache operations have been permanently disabled. The number of cache lines experiencing excessive ECC errors has reached a preset limit, 18- RAID ADG Enabler Module Missing: Indicates that write cache operations have been temperarily disabled. A RAID ADG logical drive is configured but the RAID ADG Enabler Module is broken or missing, 19- Power On Self Test (Post) ECC Errors: Indicates that write cache operations have been permanently disabled. The cache has been disabled due to a large number of ECC errors detected while testing the cache during Power On Self Test (Post), 20- Battery Hot Removed: Indicates that write cache operations have been permanently disabled. The cache has been disabled because a battery has been hot removed. [OIDs: 1.3.6.1.4.1.232.3.2.2.2.1.1, 1.3.6.1.4.1.232.3.2.2.2.1.5]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ DA Accelerator
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorNOT_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold21-20
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ DA Accelerator Error Code

    CPQ DA Accelerator Error Code

    hp.ilo.cpq.da.accelerator.battery

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.3.2.2.2.1.6
    ExpressionNULL
    DescriptionMonitors the array accelerator board battery status. Provides the status of each battery pack on the board. The batteries can only recharge when the system has power applied. Possible values are 1- Other:Indicates that the instrument agent does not recognize battery status. You may need to update your software, 2- Ok: Indicates that a particular battery pack is fully charged, 3- Charging: The battery power is less than 75%. The Drive Array Controller is attempting to recharge the battery. A battery can take as long as 36 hours to fully recharge.After 36 hours, if the battery has not recharged, it is considered failed, 4- Failed: The battery pack is below the sufficient voltage level and has not recharged in 36 hours. Your Array Accelerator board needs to be serviced, 5- Degraded:The battery is still operating, however, one of the batteries in the pack has failed to recharge properly. Your Array Accelerator board should be serviced as soon as possible, 6- NotPresent: There are no batteries associated with this controller. [OIDs: 1.3.6.1.4.1.232.3.2.2.2.1.1, 1.3.6.1.4.1.232.3.2.2.2.1.6]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ DA Accelerator
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorNOT_IN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold2,3,61-6
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ DA Accelerator Battery

    CPQ DA Accelerator Battery

    hp.ilo.cpq.da.accelerator.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.3.2.2.2.1.9
    ExpressionNULL
    DescriptionMonitors the overall condition of drive array accelerator. Possible values are 1- Other, 2- OK, 3- Degraded, 4- Failed. [OIDs: 1.3.6.1.4.1.232.3.2.2.2.1.1, 1.3.6.1.4.1.232.3.2.2.2.1.9]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ DA Accelerator
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ DA Accelerator Condition

    CPQ DA Accelerator Condition

    arraycontroller.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.3.2.2.1.1.6
    ExpressionNULL
    DescriptionMonitors the overall condition of this controller, and any associated logical drives, physical drives, and array accelerators. Possible values are 1- Other, 2-OK, 3- Degraded, 4- Failed. [OIDs: 1.3.6.1.4.1.232.3.2.2.1.1.1, 1.3.6.1.4.1.232.3.2.2.1.1.6]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ DA Array Controller Status
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Array Controller Status

    Array Controller Status

    hp.ilo.cpq.da.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.3.1.3.0
    ExpressionNULL
    DescriptionMonitors the overall condition (status) of the driver array. Possible values are 1- Other, 2- OK, 3- Degraded, 4- Failed. [OID: 1.3.6.1.4.1.232.3.1.3.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ DA Condition
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ DA Condition

    CPQ DA Condition

    logical.disk.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.3.2.3.1.1.1, 1.3.6.1.4.1.232.3.2.3.1.1.2, 1.3.6.1.4.1.232.3.2.3.1.1.11, 1.3.6.1.4.1.232.3.2.3.1.1.4
    ExpressioncpqDaLogDrvCondition
    DescriptionMonitors the overall condition of this logical drive and any associated physical drives. Possible values are 1- Other, 2-OK, 3- Degraded, 4- Failed. [OIDs: 1.3.6.1.4.1.232.3.2.3.1.1.1, 1.3.6.1.4.1.232.3.2.3.1.1.2, 1.3.6.1.4.1.232.3.2.3.1.1.11]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ DA Logical Drive
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Logical Disk Status

    Logical Disk Status

    cpq.da.physical.drive.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.3.2.5.1.1.1, 1.3.6.1.4.1.232.3.2.5.1.1.2, 1.3.6.1.4.1.232.3.2.5.1.1.37, 1.3.6.1.4.1.232.3.2.5.1.1.6
    ExpressioncpqDaPhyDrvCondition
    DescriptionMonitors the overall condition of this physical drive. Possible values are 1- Other, 2-OK, 3- Degraded, 4- Failed. [OIDs: 1.3.6.1.4.1.232.3.2.5.1.1.1, 1.3.6.1.4.1.232.3.2.5.1.1.2, 1.3.6.1.4.1.232.3.2.5.1.1.37]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ DA Physical Drive
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold3,41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ DA Physical Drive Condition

    CPQ DA Physical Drive Condition

    cpq.da.physical.drive.smartstatus

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.3.2.5.1.1.57
    ExpressionNULL
    DescriptionMonitors the physical drive S.M.A.R.T status. Possible values are 1- other: The agent is unable to determine if the status of S.M.A.R.T predictive failure monitoring for this drive, 2- ok: Indicates the drive is functioning properly, 3- replaceDrive: Indicates that the drive has a S.M.A.R.T predictive failure error and should be replaced.
    [OIDs: 1.3.6.1.4.1.232.3.2.5.1.1.1, 1.3.6.1.4.1.232.3.2.5.1.1.2, 1.3.6.1.4.1.232.3.2.5.1.1.57]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ DA Physical Drive
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold31-3
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ DA Physical Drive SMART Status

    CPQ DA Physical Drive SMART Status

    cpu.fan.thermal.health

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.6.2.6.5.0
    ExpressionNULL
    DescriptionProvides the status of the processor fan(s) in the system. This value will be one of the following:- other(1): Fan status detection is not supported by this system or driver, ok(2): All fans are operating properly, failed(4): A fan is not operating properly. System will be shutdown if the failed(4) condition occurs. [OID: 1.3.6.1.4.1.232.6.2.6.5.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Environment
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41,2,4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPU Fan Thermal Health

    CPU Fan Thermal Health

    temperature.sensors.health

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.6.2.6.3.0
    ExpressionNULL
    DescriptionProvides the status of the system's temperature sensors. This value will be one of the following:- other(1): Temp sensing is not supported by this system or driver, ok(2): All temp sensors are within normal operating range, degraded(3): A temp sensor is outside of normal operating range, failed(4): A temp sensor detects a condition that could permanently damage the system. The system will automatically shutdown if the failed(4) condition results. [OIDs: 1.3.6.1.4.1.232.6.2.6.3.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Environment
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Temperature Sensors Health

    Temperature Sensors Health

    system.fans.health

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.6.2.6.4.0
    ExpressionNULL
    DescriptionThe status of the fan(s) in the system. This value will be one of the following:- other(1): Fan status detection is not supported by this system or driver, ok(2): All fans are operating properly, degraded(3): A non-required fan is not operating properly, failed(4): A required fan is not operating properly. [OID: 1.3.6.1.4.1.232.6.2.6.4.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Environment
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    System Fan Health

    System Fan Health

    over.server.thermal.health

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.6.2.6.1.0
    ExpressionNULL
    DescriptionSpecifies the overall condition of the system's thermal environment. [OID: 1.3.6.1.4.1.232.6.2.6.1.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Environment
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Over Server Thermal Health

    Over Server Thermal Health

    hp.ilo.cpq.he.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.6.1.3.0
    ExpressionNULL
    DescriptionMonitors the overall status of the server health system. Possible values are 1- Other, 2- OK, 3- Degraded, 4- Failed. [OID: 1.3.6.1.4.1.232.6.1.3.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Environment
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ HE Condition

    CPQ HE Condition

    hp.ilo.cpq.he.asr.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.6.2.5.17.0
    ExpressionNULL
    DescriptionMonitors the overall condition of the Automatic Server Recovery (ASR) feature. Possible values are 1- Other, 2- OK, 3- Degraded, 4- Failed. [OID: 1.3.6.1.4.1.232.6.2.5.17.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Environment
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ HE ASR Condition

    CPQ HE ASR Condition

    hp.ilo.cpq.he.eventlog.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.6.2.11.2.0
    ExpressionNULL
    DescriptionMonitors the overall condition of the integrated management log feature. Possible values are 1- Other, 2- OK, 3- degraded, 4- Failed. [OID: 1.3.6.1.4.1.232.6.2.11.2.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Environment
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ HE Event Log Condition

    CPQ HE Event Log Condition

    hp.ilo.cpq.he.resillent.memory.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.6.2.14.4.0
    ExpressionNULL
    DescriptionMonitors the current condition of the Advanced Memory Protection subsystem. Possible values are 1- other: The system does not support fault tolerant memory or the state cannot be determined by the Management Agent, 2- ok: This system is operating normally, 3- degraded: The system is running in a degraded state because the Advanced Memory Protection subsystem has been engaged. [OID: 1.3.6.1.4.1.232.6.2.14.4.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Environment
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold31-3
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ HE Resilient Memory Condition

    CPQ HE Resilient Memory Condition

    cpq.ss.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.8.1.3.0
    ExpressionNULL
    DescriptionMonitors the overall condition (status) of the storage system. Possible values are 1- Other, 2- OK, 3- Degraded. [OID: 1.3.6.1.4.1.232.8.1.3.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Environment
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ SS Condition

    CPQ SS Condition

    cpq.he.fault.tolerant.powersupply.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.6.2.9.1.0
    ExpressionNULL
    DescriptionMonitors the overall condition of the fault tolerant power supply sub-system. Possible values are 1- Other, 2-OK, 3- Degraded, 4- Failed. [OID: 1.3.6.1.4.1.232.6.2.9.1.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Environment
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ HE Fault Tolerant power Supply Condition

    CPQ HE Fault Tolerant power Supply Condition

    fault.tolerant.fan.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.6.2.6.7.1.9, 1.3.6.1.4.1.232.6.2.6.7.1.1, 1.3.6.1.4.1.232.6.2.6.7.1.2
    ExpressioncpqHeFltTolFanCondition
    DescriptionProvides the condition of the fan. Possible values are 1- other: Fan status detection is not supported by this system or driver, 2- ok: The fan is operating properly, 3- degraded: A redundant fan is not operating properly, 4- failed: A non-redundant fan is not operating properly. [OIDs: 1.3.6.1.4.1.232.6.2.6.7.1.1, 1.3.6.1.4.1.232.6.2.6.7.1.2, 1.3.6.1.4.1.232.6.2.6.7.1.9]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Fault Tolerant Fan Health
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Fault Tolerant fan Status

    Fault Tolerant fan Status

    fault.tolerant.power.supply.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.6.2.9.3.1.2, 1.3.6.1.4.1.232.6.2.9.3.1.4, 1.3.6.1.4.1.232.6.2.9.3.1.1
    ExpressioncpqHeFltTolPowerSupplyCondition
    DescriptionMonitors the condition of the power supply. Possible values are 1- other: The status could not be determined or not present, 2- ok: The power supply is operating normally, 3- degraded: Power supply is outside of normal operating range, 4- failed: power supply component detects a condition that could permanently damage the system. [OIDs: 1.3.6.1.4.1.232.6.2.9.3.1.4, 1.3.6.1.4.1.232.6.2.9.3.1.1, 1.3.6.1.4.1.232.6.2.9.3.1.2]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Power Supply Health
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Fault Tolerant Power Supply Status

    Fault Tolerant Power Supply Status

    hp.ilo.cpq.he.resillentmemory.board.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.6.2.14.12.1.11
    ExpressionNULL
    DescriptionMonitors the current status of the Advanced Memory Protection memory board or cartridge or riser. Possible values are 1- other: The condition of this memory board or cartridge or riser could not be determined, 2- ok: The memory board or cartridge or riser is operating normally, 3- degraded: The memory board or cartridge or riser is in an error state. Check for correct memory installation and that the board has been inserted properly.
    [OIDs: 1.3.6.1.4.1.232.6.2.14.12.1.1, 1.3.6.1.4.1.232.6.2.14.12.1.11]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Resilient Memory 2 Board Condition
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold31-3
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ HE Resilient Memory 2 Board Condition

    CPQ HE Resilient Memory 2 Board Condition

    cpq.he.resilient.memory.2.module.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.6.2.14.13.1.20
    ExpressionNULL
    DescriptionMonitors the current status of the correctable memory errors for this memory module. Possible values are 1- other: ECC is not supported on this memory module or the condition could not be determined, 2- ok: The memory module is operating normally, 3- degraded: The memory module is correctable error count has exceeded threshold or a configuration error has been detected, 4- degradedModuleIndexUnknown: The correctable error count has exceeded threshold. The module number not available. [OIDs: 1.3.6.1.4.1.232.6.2.14.13.1.1, 1.3.6.1.4.1.232.6.2.14.13.1.20]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Resilient Memory 2 Module Condition
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold3,41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ HE Resilient Memory 2 Module Condition

    CPQ HE Resilient Memory 2 Module Condition

    temperature.sensor.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.6.2.6.8.1.1, 1.3.6.1.4.1.232.6.2.6.8.1.2, 1.3.6.1.4.1.232.6.2.6.8.1.6
    ExpressioncpqHeTemperatureCondition
    DescriptionMonitors the temperature sensor condition. Possible values are 1- other: Temperature could not be determined, 2- ok: The temperature sensor is within normal operating range, 3- degraded: The temperature sensor is outside of normal operating range, 4- failed: The temperature sensor detects a condition that could permanently damage the system. The system will automatically shutdown if the failed(4) condition results.
    [OIDs: 1.3.6.1.4.1.232.6.2.6.8.1.6, 1.3.6.1.4.1.232.6.2.6.8.1.1, 1.3.6.1.4.1.232.6.2.6.8.1.2]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ HE Temperature Sensor Health
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    Temperature Sensor Status

    Temperature Sensor Status

    cpu.usage

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.11.2.3.1.1.3
    ExpressionNULL
    DescriptionMonitors the The CPU utilization as a percentage of the theoretical maximum during the last five minutes. A value of -1 indicates that no CPU utilization information is available for this processor. [OID: 1.3.6.1.4.1.232.11.2.3.1.1.3, 1.3.6.1.4.1.232.11.2.3.1.1.1]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ Host CPU Utilization
    Unit%

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold850-100
    Warning Repeat Count21-12
    Critical OperatorGREATER_THAN_EQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold900-100
    Critical Repeat Count21-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    cpq.se.cpu.cache.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.1.2.2.3.1.2, 1.3.6.1.4.1.232.1.2.2.3.1.5, 1.3.6.1.4.1.232.1.2.2.3.1.1
    ExpressioncpqSeCpuCacheStatus
    DescriptionMonitors the status of the cache unit. If the cache is optional and not installed, unknown(1) will be returned.
    [OIDs: 1.3.6.1.4.1.232.1.2.2.3.1.1, 1.3.6.1.4.1.232.1.2.2.3.1.2, 1.3.6.1.4.1.232.1.2.2.3.1.5]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ SE CPU Cache Status
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ SE CPU Cache Status

    CPQ SE CPU Cache Status

    cpu.health

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.1.2.2.1.1.6
    ExpressionNULL
    DescriptionThe status of the processor. Possible values are 1- Unknown: The status of the CPU could not be determined, 2- OK: The CPU is functioning normally, 3- Degraded: The CPU is in a pre-failure warrantee state, 4- Failed: The CPU is in a failed state, 5- Disabled: The CPU has been disabled during power-on-self-test.
    [OIDs: 1.3.6.1.4.1.232.1.2.2.1.1.3, 1.3.6.1.4.1.232.1.2.2.1.1.6]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ SE CPU Status
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-5
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-5
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    cpq.he.se.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.1.1.3.0
    ExpressionNULL
    DescriptionMonitors the overall condition of the server. Possible values are 1- Other, 2- OK, 3- Degraded, 4- Failed.
    [OID: 1.3.6.1.4.1.232.1.1.3.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ SE Overall Condition
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ SE Condition

    CPQ SE Condition

    cpq.si.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.2.1.3.0
    ExpressionNULL
    DescriptionMonitors the overall status of the CPQ server information. Possible values are 1- Other, 2- OK, 3- Degraded, 4- Failed. [OID: 1.3.6.1.4.1.232.2.1.3.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ SI Condition
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ SI Condition

    CPQ SI Condition

    cpq.sm2.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.9.1.3.0
    ExpressionNULL
    DescriptionMonitors the overall condition of the Remote Insight/ Integrated Lights-Out. Possible values are 1- Other, 2- OK, 3- Degraded, 4- Failed. [OID: 1.3.6.1.4.1.232.9.1.3.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ SM2 ILO
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ SM2 Condition

    CPQ SM2 Condition

    cpq.sm2.controller.battery.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.9.2.2.5.0
    ExpressionNULL
    DescriptionMonitors the remote insight battery status. Possible values are 1- other: The Insight Agent is unable to determine if the battery needs replacement, 2- batteryOk: The Remote Insight battery is OK, 3- batteryFailed: The Remote Insight battery needs replacement, 4- batteryDisconnected: The Remote Insight battery is disconnected.
    [OID: 1.3.6.1.4.1.232.9.2.2.5.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ SM2 ILO
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold3,41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ SM2 Controller Battery Status

    CPQ SM2 Controller Battery Status

    cpq.sm2.controller.interface.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.9.2.2.17.0
    ExpressionNULL
    DescriptionMonitors the Remote Insight/ Integrated Lights-Out Interface Status. Possible values are 1- other: The Insight Agent is unable to determine the status of the Remote Insight/ Integrated Lights-Out interface, 2- ok: The Remote Insight/ Integrated Lights-Out firmware is responding to commands, 3- notResponding: The Remote Insight/ Integrated Lights-Out firmware is not responding to commands. [OID: 1.3.6.1.4.1.232.9.2.2.17.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ SM2 ILO
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    Filter
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold31-3
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ SM2 Controller Interface Status

    CPQ SM2 Controller Interface Status

    cpq.sm2.nic.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.9.2.5.1.1.11, 1.3.6.1.4.1.232.9.2.5.1.1.1
    ExpressioncpqSm2NicCondition
    DescriptionMonitors the overall condition of the Remote Insight/ Integrated Lights-Out Network Interface Controller (NIC). Possible values are are 1- Other, 2- OK, 3- Degraded, 4- Failed. [OIDs: 1.3.6.1.4.1.232.9.2.5.1.1.11, 1.3.6.1.4.1.232.9.2.5.1.1.5]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ SM2 NIC Condition
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ SM2 NIC Condition

    CPQ SM2 NIC Condition

    cpq.ss.box.fan.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.8.2.1.1.2, 1.3.6.1.4.1.232.8.2.1.1.7, 1.3.6.1.4.1.232.8.2.1.1.1
    ExpressioncpqSsBoxFanStatus
    DescriptionMonitors the current status of the fans in the drive box. Possible values are 1- other: Fan monitoring is not supported by this system or it is not supported by the driver, 2- ok: All fans are working normally, 3- failed: One or more storage system fans have failed. The fan(s) should be replaced immediately to avoid hardware damage, 4- noFan: This unit does not support fan monitoring, 5- degraded: At least one storage system fan has failed, but there is still sufficient cooling capacity to allow the system to continue. The fan should be replaced.
    [OIDs: 1.3.6.1.4.1.232.8.2.1.1.1, 1.3.6.1.4.1.232.8.2.1.1.2, 1.3.6.1.4.1.232.8.2.1.1.7]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ SS Box
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold3,51-5
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ SS Box Fan Status

    CPQ SS Box Fan Status

    cpq.ss.box.condition

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.8.2.1.1.8
    ExpressionNULL
    DescriptionMonitors the overall condition of the drive box. Possible values are 1- other: The agent does not recognize the status. You may need to upgrade your software, 2- ok: The storage system is operating normally. No user action is required, 3- degraded: The storage system is degraded. You need to check the temperature status or power supply status of this storage system. Additionally, if the side panel for the storage system is removed, the air flow changes could result in improper cooling of the drives and affect the temperature status, 4- failed: The storage system has failed. [OIDs: 1.3.6.1.4.1.232.8.2.1.1.2, 1.3.6.1.4.1.232.8.2.1.1.8]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ SS Box
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Warning Threshold31-4
    Warning Repeat Count11-12
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold41-4
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ SS Box Condition

    CPQ SS Box Condition

    cpq.ss.box.temperature.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.8.2.1.1.9
    ExpressionNULL
    DescriptionMonitors the temperature status of the drive system. Possible values are 1- other:Temperature monitoring is not supported by this systemor it is not supported by the driver, 2- ok:The temperature is within normal operating range, 3- degraded:The temperature is outside of normal operating range, 4- failed:The temperature could permanently damage the system.The storage system will automatically shutdown if thiscondition is detected, 5- noTemp:This unit does not support temperature monitoring. [OIDs: 1.3.6.1.4.1.232.8.2.1.1.2, 1.3.6.1.4.1.232.8.2.1.1.9]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ SS Box
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold3,41-5
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ SS Box Temperature Status

    CPQ SS Box Temperature Status

    cpq.ss.box.fault.tolerance.power.supply

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.232.8.2.1.1.11
    ExpressionNULL
    DescriptionMonitors the overall status of the fault tolerant power supply sub-system in a drive box. Possible values are 1- other: The power supply status cannot be determined, 2- ok: There are no detected power supply failures, 3- degraded: One of the power supply units in a fault tolerant power supply has failed, 4- failed: No failure conditions can currently be determined, 5- noFltTolPower: This unit does not support fault tolerant power supply monitoring. [OIDs: 1.3.6.1.4.1.232.8.2.1.1.2, 1.3.6.1.4.1.232.8.2.1.1.11]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameCPQ SS Box
    UnitNone

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency151 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorIN_LISTEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold3,41-5
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    CPQ SS Box Fault Tolerence Power Supply

    CPQ SS Box Fault Tolerence Power Supply