Description
It monitors jnx yellow alarm and jnx red alarm states.
Prerequisites
SNMP should be enabled in end device and device should support JUNIPER-ALARM-MIB OIDs and SNMP credentials should be attached against the device in portal.
Metric Parameters
| Parameter | Description |
|---|---|
| Frequency | Warning Threshold | If the metric value satisfies the condition defined along with Warning Threshold value, then a notification is sent to the user. |
| Critical Threshold | If the metric value satisfies the condition defined along with Critical Threshold value, then a notification is sent to the user. |
| Alert | The alert value can be set to either Yes or No. If it is Yes, then an alert message is sent to the user. |
Metrics
juniper.red.alarm.status
Metric Details
| Applicable for | Device |
| SNMP OID | 1.3.6.1.4.1.2636.3.4.2.3.1.0 |
| Expression | NULL |
| Description | The red alarm indication on the craft interface panel. The red alarm is on when there is some system failure or power supply failure or the system is experiencing a hardware malfunction or some threshold is being exceeded. [JUNIPER-ALARM-MIB] [1.3.6.1.4.1.2636.3.4.2.3.1] - Possible values are 1: Other, 2: Off, 3: On. The critical alert will be generated if this oid value = 3(On). The red alarm is on when there is some system failure or power supply failure or the system is experiencing a hardware malfunction or some threshold is being exceeded. |
| Category | SNMP monitors |
| Collector Type | Gateway |
| Monitor Name | Juniper Alarm State |
| Unit | None |
Possible Inputs
| Metric | Input Value | Range of Values |
|---|---|---|
| Frequency | 5 | 1 – 1440 (mins) |
| Filter | ||
| Warning Operator | ||
| Warning Threshold | ||
| Warning Repeat Count | ||
| Critical Operator | EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
| Critical Threshold | 3 | [{"1":"other"},{"2":"off"},{"3":"on"}] |
| Critical Repeat Count | 1 | 1-12 |
| Alert | Yes | Yes/No |
| Graph (Yes/No) | No | Yes/No |
Sample Output
No graph
juniper.yellow.alarm.status
Metric Details
| Applicable for | Device |
| SNMP OID | 1.3.6.1.4.1.2636.3.4.2.2.1.0 |
| Expression | NULL |
| Description | The yellow alarm state on the craft interface panel. The yellow alarm is On when there is some system warning such as maintenance alert or significant temperature increase. [JUNIPER-ALARM-MIB] [1.3.6.1.4.1.2636.3.4.2.2.1] - Possible values are 1: Other, 2: Off, 3: On. The warning alert will be generated if this oid value = 3(On). The yellow alarm is on when there is some system warning such as maintenance alert or significant temperature increase. |
| Category | SNMP monitors |
| Collector Type | Gateway |
| Monitor Name | Juniper Alarm State |
| Unit | None |
Possible Inputs
| Metric | Input Value | Range of Values |
|---|---|---|
| Frequency | 5 | 1 – 1440 (mins) |
| Filter | ||
| Warning Operator | EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
| Warning Threshold | 3 | [{"1":"other"},{"2":"off"},{"3":"on"}] |
| Warning Repeat Count | 1 | 1-12 |
| Critical Operator | ||
| Critical Threshold | ||
| Critical Repeat Count | ||
| Alert | Yes | Yes/No |
| Graph (Yes/No) | No | Yes/No |
Sample Output
No graph