Description

Monitors the PSU chassis power reserved, power allocated, power consumed, power available in redundant mode, total power available, average power used, temperature and humidity. Also it monitors PSU Outlet parameters like status, power consumed, average power, voltage and current. This template validated on Juniper QFX3000-g devices. [Using JUNIPER-POWER-SUPPLY-UNIT-MIB.mib]

Prerequisites

SNMP should be enabled in end device and device should support JUNIPER-POWER-SUPPLY-UNIT-MIB OIDs and SNMP credentials should be attached against the device in portal.

How to Apply: This template is All instance selection based. It will not ask user to select any instance(s) while assigning it to a device.

Metric Parameters

Metric Parameters
ParameterDescription
Frequency
  • Frequency is the interval in which you want to probe and collect metric data from the target device/resource
  • Frequency is defined in minutes (min).
  • Warning ThresholdIf the metric value satisfies the condition defined along with Warning Threshold value, then a notification is sent to the user.
    Critical ThresholdIf the metric value satisfies the condition defined along with Critical Threshold value, then a notification is sent to the user.
    AlertThe alert value can be set to either Yes or No. If it is Yes, then an alert message is sent to the user.

    Metrics

    juniper.psu.units.count

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.2636.3.58.1.2.1.1.0
    ExpressionNULL
    DescriptionRepresents the number of PSU units available online in the System.
    [OID: 1.3.6.1.4.1.2636.3.58.1.2.1.1.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameJuniper PSU Chassis Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    Filter
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    juniper.psu.chassis.reserved.power

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.2636.3.58.1.2.1.5.0
    ExpressionNULL
    DescriptionPower reserved for Chassis in Watts. [OID: 1.3.6.1.4.1.2636.3.58.1.2.1.5.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameJuniper PSU Chassis Monitors
    UnitW

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    Filter
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    juniper.psu.chassis.allocated.power

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.2636.3.58.1.2.1.6.0
    ExpressionNULL
    DescriptionTotal power allocated for chassis and all the FPCs in Watts. [OIDs: 1.3.6.1.4.1.2636.3.58.1.2.1.6.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameJuniper PSU Chassis Monitors
    UnitW

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    Filter
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    juniper.psu.system.consumed.power

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.2636.3.58.1.2.1.9.0
    ExpressionNULL
    DescriptionTotal power consumed by the entire system rounded to the nearest integer. This is calculated using the PowerFactor, Current and Voltage values of each PSU that is online and connected to the System. [OID: 1.3.6.1.4.1.2636.3.58.1.2.1.9.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameJuniper PSU Chassis Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    Filter
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    juniper.psu.redundant.power.avail

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.2636.3.58.1.2.1.7.0
    ExpressionNULL
    DescriptionPower(in Watts) that is still available for allocation even while supporting redundancy with the present usage. [OID: 1.3.6.1.4.1.2636.3.58.1.2.1.7.0]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameJuniper PSU Chassis Monitors
    UnitW

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    Filter
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    juniper.psu.total.power.avail

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.2636.3.58.1.2.1.8.0
    ExpressionNULL
    DescriptionPower available(in Watts) which could be made available for further allocation without supporting any redundancy with the present usage. [OID: 1.3.6.1.4.1.2636.3.58.1.2.1.8]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameJuniper PSU Chassis Monitors
    UnitW

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    Filter
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    juniper.psu.env.temperature

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.2636.3.58.1.2.3.1.1
    ExpressionNULL
    DescriptionRepresents the Temperature at each component in degrees Celsius rounded to the nearest integer. [OID: 1.3.6.1.4.1.2636.3.58.1.2.3.1.1]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameJuniper PSU Environment Monitor
    UnitC

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    juniper.psu.env.humidity

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.2636.3.58.1.2.3.1.2
    ExpressionNULL
    DescriptionHumidity at each component in percentage. [OID: 1.3.6.1.4.1.2636.3.58.1.2.3.1.2]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameJuniper PSU Environment Monitor
    Unit%

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    juniper.psu.outlet.status

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.2636.3.58.1.2.4.1.8
    ExpressionNULL
    DescriptionThe value of the operational status for the given outlet. [OID: 1.3.6.1.4.1.2636.3.58.1.2.4.1.8]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameJuniper PSU Outlet Monitors
    Unit

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical OperatorEQUALEnds with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with
    Critical Threshold0[{"0":"off"},{"1":"on"}]
    Critical Repeat Count11-12
    AlertYesYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    juniper.psu.outlet.power.consumed

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.2636.3.58.1.2.4.1.11
    ExpressionNULL
    DescriptionPower Consumed by each outlet units in Watts. [OID: 1.3.6.1.4.1.2636.3.58.1.2.4.1.11]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameJuniper PSU Outlet Monitors
    UnitW

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    juniper.psu.outlet.avg.power.used

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.2636.3.58.1.2.4.1.3
    ExpressionNULL
    DescriptionBuffer that contains the average power used, in Watts for each component.
    [OID: 1.3.6.1.4.1.2636.3.58.1.2.4.1.3]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameJuniper PSU Outlet Monitors
    UnitW

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    juniper.psu.outlet.voltage

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.2636.3.58.1.2.4.1.9
    ExpressionNULL
    DescriptionOutput voltage in Volts rounded to the nearest integer. [OID: 1.3.6.1.4.1.2636.3.58.1.2.4.1.9]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameJuniper PSU Outlet Monitors
    Unitv

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    juniper.psu.outlet.current

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.2636.3.58.1.2.4.1.5
    ExpressionNULL
    DescriptionPSU output current in milliamps rounded to the nearest integer. [OID: 1.3.6.1.4.1.2636.3.58.1.2.4.1.5]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameJuniper PSU Outlet Monitors
    UnitmA

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph

    juniper.psu.avg.power.used

    Metric Details

    Metric Details
    Applicable forDevice
    SNMP OID1.3.6.1.4.1.2636.3.58.1.2.2.1.1
    ExpressionNULL
    DescriptionBuffer that contains the average power used, in Watts for each component.
    [OID: 1.3.6.1.4.1.2636.3.58.1.2.2.1.1]
    CategorySNMP monitors
    Collector TypeGateway
    Monitor NameJuniper PSU Power
    UnitW

    Possible Inputs

    Possible Inputs
    MetricInput ValueRange of Values
    Frequency51 – 1440 (mins)
    FilterNULLNot Applicable
    Warning Operator
    Warning Threshold
    Warning Repeat Count
    Critical Operator
    Critical Threshold
    Critical Repeat Count
    AlertNoYes/No
    Graph (Yes/No)YesYes/No

    Sample Output

    No graph