Description
Applicable on the Riverbed Steelhead devices. Monitors the system health, CPU utilization, CPU load, Disk utilization, temperature, aggregated bandwidth, pass-through traffic, optimization service status, etc.
Prerequisites
SNMP should be enabled in end device and device should support STEELHEAD-MIB and SNMP credentials should be attached against the device in portal.
Metric Parameters
Parameter | Description |
---|---|
Frequency | Warning Threshold | If the metric value satisfies the condition defined along with Warning Threshold value, then a notification is sent to the user. |
Critical Threshold | If the metric value satisfies the condition defined along with Critical Threshold value, then a notification is sent to the user. |
Alert | The alert value can be set to either Yes or No. If it is Yes, then an alert message is sent to the user. |
Metrics
rs.service.uptime
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.2.4.0 |
Expression | serviceUptime/100 |
Description | Uptime of the optimization service. [OID: 1.3.6.1.4.1.17163.1.1.2.4.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit | s |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | LESS_THAN_EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Critical Threshold | 1800 | 0 - 4294967295 |
Critical Repeat Count | 1 | 1-12 |
Alert | Yes | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
system.cpu.utilization
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.1.4.0 |
Expression | NULL |
Description | The percentage CPU utilization, aggregated across all CPUs, rolling average over the past minute. [OID: 1.3.6.1.4.1.17163.1.1.5.1.4.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit | % |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | GREATER_THAN_EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Warning Threshold | 80 | 0-100 |
Warning Repeat Count | 3 | 1-12 |
Critical Operator | GREATER_THAN_EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Critical Threshold | 90 | 0-100 |
Critical Repeat Count | 3 | 1-12 |
Alert | Yes | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.system.temperature
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.2.9.0 |
Expression | NULL |
Description | Indicates the temperature of the system (C) [OID: 1.3.6.1.4.1.17163.1.1.2.9.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit | C |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | GREATER_THAN_EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Warning Threshold | 60 | 0 - 2147483647 |
Warning Repeat Count | 1 | 1-12 |
Critical Operator | GREATER_THAN_EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Critical Threshold | 65 | 0 - 2147483647 |
Critical Repeat Count | 1 | 1-12 |
Alert | Yes | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.optimized.connections
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.2.1.0 |
Expression | NULL |
Description | Current total number of optimized connections. [OID: 1.3.6.1.4.1.17163.1.1.5.2.1.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.passthrough.connections
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.2.2.0 |
Expression | NULL |
Description | Current total number of pass-through connections. [OID: 1.3.6.1.4.1.17163.1.1.5.2.2.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.halfopened.connections
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.2.3.0 |
Expression | NULL |
Description | Current total number of half-opened (optimized) connections. [OID: 1.3.6.1.4.1.17163.1.1.5.2.3.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.halfclosed.connections
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.2.4.0 |
Expression | NULL |
Description | Current total number of half-closed (optimized) connections. [OID: 1.3.6.1.4.1.17163.1.1.5.2.4.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.established.connections
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.2.5.0 |
Expression | NULL |
Description | Current number of established (optimized) connections. [OID: 1.3.6.1.4.1.17163.1.1.5.2.5.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.active.connections
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.2.6.0 |
Expression | NULL |
Description | Current number of active (optimized) connections. [OID: 1.3.6.1.4.1.17163.1.1.5.2.6.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.total.connections
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.2.7.0 |
Expression | NULL |
Description | Total number of connections. [OID: 1.3.6.1.4.1.17163.1.1.5.2.7.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.inbound.lan.traffic
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.3.1.1.0, 1.3.6.1.4.1.17163.1.1.5.6.1.1.0 |
Expression | if(isDef(bwHCAggInLan),bwHCAggInLan,bwAggInLan) |
Description | Rate of total optimized bytes across all application ports, in the WAN to LAN direction since the last restart of service, as measured on the LAN side. [OID: 1.3.6.1.4.1.17163.1.1.5.3.1.1.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit | Bps |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.inbound.wan.traffic
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.3.1.2.0, 1.3.6.1.4.1.17163.1.1.5.6.1.2.0 |
Expression | if(isDef(bwHCAggInWan),bwHCAggInWan,bwAggInWan) |
Description | Rate of total optimized bytes across all application ports, in the WAN to LAN direction since the last restart of service, as measured on the WAN side. [OID: 1.3.6.1.4.1.17163.1.1.5.3.1.2.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit | Bps |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.outbound.lan.traffic
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.3.1.3.0, 1.3.6.1.4.1.17163.1.1.5.6.1.3.0 |
Expression | if(isDef(bwHCAggOutLan),bwHCAggOutLan,bwAggOutLan) |
Description | Rate of total optimized bytes across all application ports, in the LAN to WAN direction since the last restart of service, as measured on the LAN side. [OID: 1.3.6.1.4.1.17163.1.1.5.3.1.3.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit | Bps |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.outbound.wan.traffic
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.3.1.4.0, 1.3.6.1.4.1.17163.1.1.5.6.1.4.0 |
Expression | if(isDef(bwAggHCOutWan),bwAggHCOutWan,bwAggOutWan) |
Description | Rate of total optimized bytes across all application ports, in the LAN to WAN direction since the last restart of service, as measured on the WAN side. [OID: 1.3.6.1.4.1.17163.1.1.5.3.1.4.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit | Bps |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.datastore.hit.rate
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.4.1.0 |
Expression | NULL |
Description | Rate of datastore hits. [OID: 1.3.6.1.4.1.17163.1.1.5.4.1.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit | psec |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.datastore.miss.rate
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.4.2.0 |
Expression | NULL |
Description | Rate of the datastore misses. [OID: 1.3.6.1.4.1.17163.1.1.5.4.2.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit | psec |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.passthrough.traffic.in
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.3.3.1.0 |
Expression | NULL |
Description | Rate of passthrough bytes in WAN to LAN direction. [OID: 1.3.6.1.4.1.17163.1.1.5.3.3.1.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit | Bps |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.passthrough.traffic.out
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.3.3.2.0 |
Expression | NULL |
Description | Rate of passthrough bytes in LAN to WAN direction. [OID: 1.3.6.1.4.1.17163.1.1.5.3.3.2.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit | Bps |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.passthrough.traffic.total
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.3.3.3.0 |
Expression | NULL |
Description | Rate of total passthrough bytes. [OID: 1.3.6.1.4.1.17163.1.1.5.3.3.3.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit | Bps |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.system.health
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.2.7.0, 1.3.6.1.4.1.17163.1.1.2.10.0 |
Expression | systemHealth |
Description | Provides the Current health of the system. This variable is identical to health except that it is of integer datatype. Possible states are 10000-healthy, 30000-degraded, 31000-admissionControl, 50000-critical. [OID: 1.3.6.1.4.1.17163.1.1.2.7.0, 1.3.6.1.4.1.17163.1.1.2.10.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | NOT_EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Critical Threshold | 10000 | [{"10000":"healthy"},{"30000":"degraded"},{"31000":"admissionControl"},{"50000":"critical"}] |
Critical Repeat Count | 1 | 1-12 |
Alert | Yes | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.opt.service.status
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.2.8.0 |
Expression | NULL |
Description | Provides the status of the optimization service. Possible values are 0-none, 1-unmanaged, 2-running , 3-sentCom1, 4-sentTerm1, 5-sentTerm2, 6-sentTerm3, 7-pending , 8-stopped. [OID: 1.3.6.1.4.1.17163.1.1.2.8.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | NOT_EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Critical Threshold | 2 | [{"0":"none"},{"1":"unmanaged"},{"2":"running"},{"3":"sentCom1"},{"4":"sentTerm1"},{"5":"sentTerm2"},{"6":"sentTerm3"},{"7":"pending"},{"8":"stopped"}] |
Critical Repeat Count | 1 | 1-12 |
Alert | Yes | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
rs.data.store.disk.utilization
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.4.4.0 |
Expression | NULL |
Description | Provides the average disk utilization in percentage. [OID: 1.3.6.1.4.1.17163.1.1.5.4.4] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit | % |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | GREATER_THAN_EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Warning Threshold | 75 | 0-100 |
Warning Repeat Count | 1 | 1-12 |
Critical Operator | GREATER_THAN_EQUAL | Ends with, ==, !=, >=, <=, >, <, In Range, Out of range, Equals, Not equals, Equals Ignore Case, Not Equals Ignore Case, Contains, Not contains, Regex match, Regex no match, In string list, Not in string list, In List, Not in list, Starts with |
Critical Threshold | 80 | 0-100 |
Critical Repeat Count | 1 | 1-12 |
Alert | Yes | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph
system.cpu.load.5min
Metric Details
Applicable for | Device |
SNMP OID | 1.3.6.1.4.1.17163.1.1.5.1.2.0 |
Expression | cpuLoad5 / 100 |
Description | Five-minute CPU load in hundreths. [OID: 1.3.6.1.4.1.17163.1.1.5.1.2.0] |
Category | SNMP monitors |
Collector Type | Gateway |
Monitor Name | Riverbed Steelhead Perf and Statistics Monitor |
Unit |
Possible Inputs
Metric | Input Value | Range of Values |
---|---|---|
Frequency | 5 | 1 – 1440 (mins) |
Filter | ||
Warning Operator | ||
Warning Threshold | ||
Warning Repeat Count | ||
Critical Operator | ||
Critical Threshold | ||
Critical Repeat Count | ||
Alert | No | Yes/No |
Graph (Yes/No) | Yes | Yes/No |
Sample Output
No graph